Printable Pumpkin Templates for Carving

Free printable pumpkin templates sized to your pumpkin: 12 original carving stencils, a face builder and a name stencil, with cut and shave areas marked.

Stencil
Face builder

Page preview

Cut black · shave grey

Midnight bat · 180 mm art · US Letter

How to make a pumpkin carving template

  1. Pick a stencil from the gallery. The blank outline is useful if you want to draw your own design.
  2. Measure the pumpkin. Enter the usable width and height in millimetres. The tool uses the smaller value so the design stays inside the face.
  3. Choose mirror if the pattern will be transferred ink-side down or if you want the design reversed.
  4. Download the PDF and print at 100 %. Check the test line before you cut.
  5. Tape the stencil to the pumpkin, prick the outline, remove the paper and carve the black shapes.

The preview uses the same drawing as the PDF. A dashed square around the stencil shows the art area, so you can see how much of the pumpkin face the design will cover before you print.

The gallery has twelve original designs and a blank outline. The set includes a bat, a cat, a ghost, an owl, a spider, a crescent moon, a tree, a skull, a star shower, falling leaves, a witch hat and a jack-o’-lantern face. They are grouped as classic, cute and spooky, but the groups are only a guide; any design can be printed at any size.

The blank outline prints only the dashed art square. Use it as a frame for a hand-drawn face or as a guide when you want to enlarge a sketch. The design shapes are simple enough to cut with a small serrated knife, but detailed enough to look intentional on a porch.

Sizing the stencil to the pumpkin

A pumpkin is not flat. The widest face is usually between the stem and the base, and the usable width is narrower than the diameter because the sides curve away. Measure the height from the stem to the base, then measure the width across the flattest part of the face. Enter both numbers.

The tool scales the art to the smaller of the width and height. A 180 mm pumpkin and a 180 mm stencil fill the face; a 240 mm wide pumpkin with a 180 mm height still gets a 180 mm stencil, centred. If you want a smaller design, reduce both numbers; do not stretch a square design into a narrow oval.

For a very large pumpkin, print the stencil on Tabloid or A3 if your printer supports it, or use the tiled output and tape the pages together. Match the joins carefully: the dashed art square is the alignment guide.

Cutting and shaving

Black shapes are through-cuts. Remove the pumpkin wall completely. Grey shapes are shave areas: scrape the coloured skin away until the pale flesh shows, but do not break through. A shave area glows softly and gives a design more depth than a cut-only face.

Cut the largest shapes first and work inward. A small serrated knife or a pumpkin saw gives more control than a kitchen knife. Push the blade in with a gentle sawing motion rather than forcing it. If a shape is very narrow, cut it in two passes from the front and the back.

The face builder and the name stencil

The face builder combines three choices: eyes, nose and mouth. The shapes are designed to sit on the same face grid, so the result looks like one pumpkin rather than three separate stickers. You can leave the nose out, use round eyes instead of triangles, or choose a smile instead of teeth.

The name stencil turns letters and numbers into block outlines. It is useful for a house number, a party table or a pumpkin for a community centre. The letters are limited to A–Z, 0–9 and spaces. A name that is too long is trimmed to eighteen characters so the page stays readable.

Paper, transfer and safety

Ordinary printer paper works for a stencil that will be used once. Card stock holds its shape better on a curved pumpkin and is easier to tape down. If the pumpkin is wet, dry it first; tape does not stick to a damp skin and the ink may run.

Carve on a washable surface, keep the knife away from your fingers, and cut away from your body. Children should not handle the knife; they can help with the pin pricks and with separating the cut pieces. A small battery tea light is safer than a candle, especially near paper or curtains.

Printing tips

  • Print on one side only.
  • Choose Actual size or 100 %.
  • Check the test line: 2 in on Letter, 50 mm on A4.
  • Print one stencil before a batch; paper thickness and printer margins vary.
  • Use the share link to send the exact pattern and size to someone else.

The PDF does not include a logo or a website address on the stencil itself. Your settings stay in this browser, and Clear my data removes them. The share link carries only the pattern, size, mirror and paper choice.

Updated:

Frequently asked questions

Are the pumpkin templates original?

Yes. The stencils in this tool are drawn for PrintableMate. They are not copied from a competitor, a book or a film. You can print them for home, school or community events. Please do not resell the files themselves.

How do I size a stencil to my pumpkin?

Measure the height and the widest usable face of your pumpkin in millimetres. Enter both values. The stencil is scaled to the smaller of the two measurements so it fits inside the face without running over the curve. Leave a margin at the top and bottom for the stem and the base.

What does 'mirror' do?

Mirror flips the stencil left to right. Use it when you tape the pattern to the pumpkin and the ink side faces the skin, or when a face should look the other way. The PDF preview and the printed page use the same mirror setting, so what you see is what you cut.

How do I transfer the pattern to the pumpkin?

Print at 100 %, cut roughly around the stencil, and tape it to the pumpkin. Smooth the paper over the curve. Use a pin or a thin skewer to prick through the outline every few millimetres. Remove the paper and rub a little flour or chalk dust over the holes so the line is visible before you cut.

What do the black and grey areas mean?

Black is cut all the way through the pumpkin wall. Grey is a shave area: remove only the outer skin so light glows through the flesh. Not every stencil has a shave area. If you do not want to shave, cut the black shapes only and leave the grey parts intact.

Can I make a name stencil?

Yes. Type letters or numbers, choose the size, and print the name stencil. The letters are drawn as block outlines that you cut out and use as a template. The name is limited to letters, numbers and spaces so the shapes stay clean and the page stays printable.

How many stencils can I print?

You can print any stencil as many times as you need. The gallery has twelve designs plus a blank outline. The face builder combines eyes, a nose and a mouth. The name stencil makes a separate page. There is no watermark and no sign-up.

How do I print the template at the right size?

Print at 100 % or Actual size, not Fit to page, and use the same paper size as the PDF. Check the test line at the bottom: 2 in on Letter or 50 mm on A4. If the line is short, the stencil will be too small. Reprint with 'Actual size' selected.