5160 Label Template (compatible with Avery® 5160)

Print 30 labels per sheet with this free 5160 label template, compatible with Avery® 5160 sheets — each label lands at its exact 1 × 2-5/8 in position.

30 labels · 1 × 2-5/8 in · Letter 8.5 × 11 incompatible with Avery® 5160

Avery® is a registered trademark of its owner. PrintableMate is not affiliated with or endorsed by Avery.

Label
2-5/8 × 1 in 66.675 × 25.4 mm
Top margin
1/2 in 12.7 mm
Side margin
3/16 in 4.7625 mm
Pitch
2-3/4 × 1 in 69.85 × 25.4 mm
Label text
Logo, barcode and border
Mail merge list

Numbered labels
Alignment fix

Measure the printed test page, then nudge until the outlines sit inside the labels.

Check my sheet

Your text and lists stay in this browser. Nothing is uploaded.

5160 sheet preview

Page 1 / 1

Ready

Print at 100 % (Actual size) — never “Fit to page”. Hold the test print against a label sheet before a large run.

Avery® is a registered trademark of its owner. PrintableMate is not affiliated with or endorsed by Avery.

5160 label size and layout

A 5160-compatible sheet is a Letter page with 30 labels: three across and ten down. Each label measures 1 × 2-5/8 inches, or 25.4 × 66.675 millimetres. The layout uses a 1/2 inch top and bottom margin, a 3/16 inch side margin, a 1/8 inch gap between columns and no vertical gap between rows. The horizontal pitch is 2-3/4 inches and the vertical pitch is 1 inch.

The measurements matter because a word-processor table can look correct on screen and still push the last row down. A PDF built from page coordinates does not reflow when the text changes. The position of label 1, label 19 and label 30 is fixed before you type.

Measure Inches Millimetres
Label 2-5/8 × 1 66.675 × 25.4
Layout 3 across × 10 down = 30 —
Page Letter 8.5 × 11 215.9 × 279.4
Top and bottom margin 1/2 12.7
Left and right margin 3/16 4.7625
Gap between columns 1/8 3.175
Horizontal pitch 2-3/4 69.85
Vertical pitch 1 25.4

These figures describe the common 30-up layout used by 5160-compatible sheets. Always compare them with the writing on your own packet. Store-brand packs sometimes use a different margin even when the label size and count look the same.

Avery® is a registered trademark of its owner. PrintableMate is not affiliated with or endorsed by Avery.

How to print on 5160-compatible sheets

First, run a test print on plain paper. Choose Test print in the tool, print at 100 percent on Letter paper, and place the sheet behind a real label sheet against a window. Look at the corners of label 1, label 3, label 28 and label 30. They should sit inside the die-cuts without crossing an edge. The test page also includes a 100 mm ruler, so you can check whether the printer is scaling the output.

Second, fill the labels. For a single design, type the text once and it repeats across all 30 labels. For a mailing list, switch to List mode and paste rows from a spreadsheet. For numbered labels, use Numbered mode and set the prefix, start value, step and padding.

Third, download the PDF and print it from a desktop PDF viewer. Select Letter paper, portrait orientation and 100 percent or Actual size. Turn off “Fit to page”, “Shrink to fit” and similar options. If the printer pulls label sheets crooked, load one sheet at a time and check which side faces up by marking a plain sheet first.

Finally, keep the PDF. A saved file can be reprinted without recreating the design, which is useful for regular address labels or a product label that changes only once a year.

Fill a sheet or merge a mailing list

Same mode fills all 30 labels with one design. It is the quickest way to print a sheet of return address labels or identical product labels. The grey placeholders in the preview are never printed; they only show where text will sit.

List mode treats each spreadsheet row as a label. Copy the cells from Excel or Google Sheets, including the header row, or upload a CSV file. The tool looks for columns such as name, address, city, state and ZIP, and you can correct the mapping before printing. Thirty rows fill one page, so 240 addresses produce eight sheets. Rows with no address can be skipped, and a ZIP code that lost its leading zero is repaired with a warning.

Numbered mode is for labels that need a sequence rather than a list. Enter ASSET- as the prefix, start at 1, step by 1 and pad to four digits. The sheet then prints ASSET-0001 through ASSET-0030. The order follows the sheet layout, not a separate database.

For return labels, address formats and row-by-row selection, the address label workflow is a better fit than a single locked sheet.

Fix alignment in two minutes

Start by deciding whether the problem is offset or drift. An offset moves every label by the same distance: the whole grid is 1 mm to the right or 2 mm down. Drift gets worse as you move across or down the page, which points to scaling or a paper-size mismatch.

For an offset, measure from the paper edge to the first label and enter the difference, or use the nudge controls in 0.1 mm steps. For drift, check the printed 100 mm ruler. If it measures less than 100 mm, the PDF is being reduced. A 3 percent reduction over a 10 inch page moves the bottom row by about 0.3 inches, which is enough to miss the last row completely.

Once a nudge works, save it as a profile. The setting stays on this device and appears on the Download button, so the next sheet starts from the corrected position. A profile is tied to Letter paper; an A4 profile should not be reused with a Letter sheet.

Printing a partial sheet

A half-used pack is still useful. Open the start map and tap the first free position. The design begins at that label and the remaining positions continue in the chosen order. A list started at label 19 uses labels 19 to 30 on the first page, then continues at label 1 on the next sheet.

Peel used labels carefully so the carrier sheet stays flat, and check that no torn edges sit under the next label. If the sheet has been stored in a humid room, let it flatten before feeding it through the printer.

Other 30-per-sheet labels this fits

The same layout is used by several 30-up products, including sheets described as compatible with Avery® 5260 and 8160. “Compatible” means the label size, count and pitch match the 5160 layout; it does not mean the sheet is made or endorsed by the brand. Check your packet and run the sheet comparison before printing a large run.

If your pack uses a different label size or margin, use the Label Maker and enter the measurements as a custom sheet. The 5160 page deliberately keeps one sheet so the measurements, step bar and alignment advice stay focused.

Avery® is a registered trademark of its owner. PrintableMate is not affiliated with or endorsed by Avery.

Why a PDF beats a word-processor template

A word-processor label template is a table. When a line wraps or a font changes, the row can grow and push every label below it out of position. Hidden cell margins can add another small offset. A PDF does not reflow: each label is drawn at a fixed point on the page, and the same file prints the same way on another computer.

A PDF also avoids the “template not found” problem. There is no add-in, no macro and no version of Word to match. You can open the file in any PDF viewer, print it at 100 percent, and keep it for reprints. Positions are expressed in points, with 72 points to an inch, so the printer receives an unambiguous physical size.

The trade-off is that a PDF is not a document to edit later. Keep the design saved in the tool, or save the PDF and recreate the text if it changes. For a recurring mailing, saving the source list and the design is usually faster than editing a table template.

Updated:

Frequently asked questions

What size is a 5160 label?

Each label is 1 × 2-5/8 inches, or 25.4 × 66.675 millimetres. A Letter sheet holds 30 labels in three columns and ten rows, with a 1/2 inch top margin, 3/16 inch side margins and a 1/8 inch gap between columns.

How do I download a free 5160 template?

There is nothing to download first. Enter your text or paste a list, download the finished PDF, and print it at 100 percent on Letter paper. The file is free, needs no account and contains no watermark.

Do I need Word to print 5160 labels?

No. This works in a browser on Windows, macOS, ChromeOS, Linux, Android and iOS. You can paste cells from any spreadsheet or upload a CSV, then download a PDF that prints into the 30 labels.

Is this template free, and do I need an account?

It is free and there is no account. Ads may appear on the page around the tool, but the PDF contains only your labels. You can make as many sheets as you need and reprint a saved PDF later.

Why do my labels print off-centre or drift down the page?

A small uniform shift is usually a printer offset; a growing error is usually scaling. Print a plain-paper test at 100 percent, check the first and last labels, turn off “Fit to page”, and use the alignment nudge only after confirming the paper size is Letter.

How do I print a mailing list on 5160 labels?

Switch to List mode, paste rows from Excel or Google Sheets, or upload a CSV. Each row becomes one label and 30 rows fill a page. Check the column mapping, especially the ZIP column, before downloading the PDF.

Can I start halfway down a used sheet?

Yes. Open the start map, tap the first free label, and the design begins there. Labels from a list continue in order on the next sheet, so a partly used pack does not have to be thrown away.

Is this an official Avery® template?

No. It is an independent template compatible with Avery® 5160. PrintableMate is not affiliated with or endorsed by the trademark owner. The layout is based on published label dimensions and our own test prints.