Cone Template

Print a cone template in the exact size you need: enter the base diameter and height, add a top diameter for an open cone, and get the pattern with a glue tab.

Cone size
Clay and paper

Page preview

Sector pattern

Slant 130.0 mm · angle 138.46° · arc 314.2 mm · fits on 1 letter page

How the cone calculator works

A cone pattern is a sector: part of a circle with a curved edge and two straight sides. The straight sides meet at the tip for a pointed cone. For a truncated cone they stop at an inner arc. The curved edge becomes the base; the straight edges meet at the glue seam.

The tool uses three inputs: base diameter, height and, optionally, top diameter. From these it calculates the slant height, the sector radius, the sector angle and the chord. You do not need to do the trigonometry by hand. The numbers are shown under the preview so you can check the scale or draw the pattern with a compass.

For a pointed cone, the base radius is r, the height is h, and the slant height is √(r² + h²). The sector radius equals the slant height. The angle is 360° × r / slant. For a frustum, the pattern is the difference between two sectors with the same centre.

Pointed cone and truncated cone

A pointed cone is the classic party-hat or tree shape. Set the top diameter to zero, or choose Pointed. The pattern is a single sector and the tip is a sharp point. The tip is fragile on card; leave a small flat area or reinforce it with tape on the inside.

A truncated cone has a flat top. Set the top diameter to the opening you need. The pattern becomes a curved band between an outer arc and an inner arc. The inner arc is the top opening. This is the shape for a lampshade, a planter liner, a cone-shaped cup or a hat with a flat crown.

The top diameter must be smaller than the base diameter. If the two are equal, the shape is a cylinder, not a cone. The tool warns you rather than drawing an impossible pattern.

Shrink and finished size

Clay, papier-mâché and some 3D-printing filaments shrink as they dry or cool. A pottery body might shrink 10 % from wet clay to fired ware. If you want the finished cone to have a 100 mm opening, the wet pattern must start larger. Enter the shrink percentage and the tool scales the pattern up.

The shrink value is a percentage of the finished size, not a multiplier on the pattern. A 10 % shrink means the finished size is 90 % of the wet size, so the pattern is divided by 0.9. Use the value from your clay supplier or from a test piece; a guess can be off by several millimetres on a large cone.

Tabs, seams and assembly

The glue tab is a narrow strip along one straight edge. A small notch at the base and the top lets the tab bend around the curve without buckling. Apply glue to the tab, overlap the other straight edge, and press from the base to the tip. Hold until the glue grabs.

For a paper hat, double-sided tape is faster and does not wrinkle the paper. For card, white glue or a hot glue gun is stronger. For a waterproof cone, use a plastic sheet or coat the paper with a sealant after assembly. Test any coating on a scrap first.

Tiling and large patterns

A large sector does not fit on one sheet. The tool splits it into tiles with a 10 mm overlap. Print all pages, trim the overlap on one side of each join, and align the printed guides. Tape the joins on the back so the front stays smooth.

The tile map shows the page order. Keep the pages flat and join them in pairs before joining the pairs; a long seam is harder to keep straight. For a very large cone, trace the assembled pattern onto card or board and cut once.

Drawing it by hand

If you do not have a printer, use the numbers in the summary. Set a compass to the sector radius and draw an arc. Mark the sector angle with a protractor from the centre. For a frustum, draw the inner arc at the inner radius. The chord is the straight-line distance between the ends of the arc; it is a quick check that your angle is correct.

A beam compass or a piece of string and a pencil works for a radius longer than your compass. Keep the string tight and the pencil vertical. A small error in the radius becomes a larger error at the seam on a big cone.

Paper, card and materials

Ordinary paper is fine for a template or a small hat. Card stock holds the cone shape and resists creasing at the seam. For a food contact cone, use food-safe paper and do not use recycled or printed paper on the inside. For a lamp, use a shade material rated for the heat of the bulb and keep the bulb away from the paper.

Score the curved edge before folding if the material is stiff. Do not score the straight seam; it should stay flat for gluing. A bone folder or an empty ballpoint pen gives a clean fold on card.

Printing tips

  • Print at 100 % and check the test line.
  • Keep the tab on unless you are tracing the pattern.
  • Use the share link to send the exact size to someone else.
  • Print a small test cone before a large one; the seam is the part that goes wrong.

The PDF has no ads, logo or website address on the pattern. Your settings stay in this browser, and Clear my data removes them. The share link carries the dimensions, tab and paper choice.

Updated:

Frequently asked questions

How do I make a cone template?

Enter the base diameter and the height you want. The tool calculates the slant height, the sector radius and the angle, then draws the pattern at full size. Add a top diameter for a truncated cone. Print at 100 %, cut on the solid line and fold the tab.

What is a truncated cone?

A truncated cone, or frustum, has a flat top instead of a point. It is used for lampshades, planters, cups and party hats with a flat crown. Add a top diameter larger than zero and the tool draws a curved band instead of a full sector.

What do the numbers mean?

The base diameter is the wide opening. The height is the vertical distance between the base and the top or point. The slant height is the distance along the surface. The sector radius is the radius you draw on paper. The angle is how much of a full circle the sector covers.

What is shrink and why does it matter?

Some materials shrink when they dry or fire. Pottery clay can shrink 8–15 % depending on the body and firing. If you want a finished cone of a given size, turn on shrink and enter the percentage. The pattern is enlarged so the finished piece comes out at the size you asked for.

How do I add a glue tab?

Leave the tab on. The default is a 10 mm tab along one straight edge, with a small notch so the seam sits flat. For thin paper, 8 mm is enough. For card, 12–15 mm gives more surface. Turn the tab off for a template you will trace rather than glue.

Can I print a cone larger than one sheet?

Yes. The pattern is split into tiles with a small overlap and crop marks. Print the tiles, trim the overlap on one side of each join, line up the guides and tape the back. The summary shows how many pages the pattern needs.

How do I draw a cone without a printer?

Use the calculated sector radius and angle with a compass and a protractor. Set the compass to the sector radius, draw an arc, then mark the angle from the pattern. The tool also shows the chord length, which is the straight distance between the two ends of the arc.

How do I print the pattern at the right size?

Print at 100 % or Actual size, not Fit to page. Use the same paper size as the PDF and measure the test line: 2 in on Letter or 50 mm on A4. The pattern is only exact if the print is not scaled. A 1 % shrink can make a noticeable gap at the seam on a large cone.